RepRap/Configs/Slic3r: Unterschied zwischen den Versionen

Aus Stratum 0
Wechseln zu:Navigation, Suche
(neue configs)
(→‎aktuelle configs: Kasalehlias Configs hinzugefügt)
Zeile 15: Zeile 15:
 
Eine funktionierende, aber noch nicht sehr fein justierte config ist diese:
 
Eine funktionierende, aber noch nicht sehr fein justierte config ist diese:
 
==== larsan ====
 
==== larsan ====
−
<pre style="height:200px;overflow:scroll;">
+
<pre style="height:200px;overflow-y:scroll;">
 
# generated by Slic3r 0.9.10 on Sun Sep 29 22:51:39 2013
 
# generated by Slic3r 0.9.10 on Sun Sep 29 22:51:39 2013
 
avoid_crossing_perimeters = 0
 
avoid_crossing_perimeters = 0
Zeile 131: Zeile 131:
 
z_offset = 0
 
z_offset = 0
 
</pre>
 
</pre>
 +
 +
==== Kasalehlia ====
 +
etwas auf den neuen Drucker angepasst. Start G-Code und neuer Lüfter am Druckkopf sind berücksichtigt.
 +
 +
Printer:
 +
<pre style="height:200px;overflow-y:scroll;">
 +
bed_size = 200,200
 +
end_gcode = M107; fan off\nM104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84    ; disable motors
 +
extruder_offset = 0x0
 +
gcode_flavor = reprap
 +
layer_gcode =
 +
nozzle_diameter = 0.5
 +
print_center = 100,80
 +
retract_before_travel = 2
 +
retract_layer_change = 1
 +
retract_length = 1
 +
retract_length_toolchange = 10
 +
retract_lift = 0
 +
retract_restart_extra = 0
 +
retract_restart_extra_toolchange = 0
 +
retract_speed = 30
 +
start_gcode = G28 X0 Y0 ; home X and Y\nG0 X60; move to X60\nG92 X0; set postition to X=0\nG28 Z0; home Z\nM106; fan on
 +
toolchange_gcode =
 +
use_firmware_retraction = 0
 +
use_relative_e_distances = 0
 +
vibration_limit = 0
 +
wipe = 0
 +
z_offset = 0
 +
</pre>
 +
 +
Normales PLA:
 +
<pre style="height:200px;overflow-y:scroll;">
 +
bed_temperature = 50
 +
bridge_fan_speed = 100
 +
cooling = 1
 +
disable_fan_first_layers = 1
 +
extrusion_multiplier = 1
 +
fan_always_on = 0
 +
fan_below_layer_time = 60
 +
filament_diameter = 1.75
 +
first_layer_bed_temperature = 55
 +
first_layer_temperature = 200
 +
max_fan_speed = 100
 +
min_fan_speed = 35
 +
min_print_speed = 10
 +
slowdown_below_layer_time = 30
 +
temperature = 195
 +
</pre>
 +
 +
Holz PLA:
 +
<pre style="height:200px;overflow-y:scroll;">
 +
bed_temperature = 50
 +
bridge_fan_speed = 100
 +
cooling = 1
 +
disable_fan_first_layers = 1
 +
extrusion_multiplier = 1
 +
fan_always_on = 0
 +
fan_below_layer_time = 60
 +
filament_diameter = 1.75
 +
first_layer_bed_temperature = 55
 +
first_layer_temperature = 210
 +
max_fan_speed = 100
 +
min_fan_speed = 35
 +
min_print_speed = 10
 +
slowdown_below_layer_time = 30
 +
temperature = 210
 +
</pre>
 +
 +
Matetags oder andere Filigranere Dinge:
 +
<pre style="height:200px;overflow-y:scroll;">
 +
avoid_crossing_perimeters = 0
 +
bottom_solid_layers = 3
 +
bridge_acceleration = 0
 +
bridge_flow_ratio = 1
 +
bridge_speed = 60
 +
brim_width = 3
 +
complete_objects = 0
 +
default_acceleration = 0
 +
external_perimeter_speed = 70%
 +
external_perimeters_first = 0
 +
extra_perimeters = 1
 +
extruder_clearance_height = 20
 +
extruder_clearance_radius = 20
 +
extrusion_width = 0
 +
fill_angle = 45
 +
fill_density = 1
 +
fill_pattern = rectilinear
 +
first_layer_acceleration = 0
 +
first_layer_extrusion_width = 200%
 +
first_layer_height = 0.22
 +
first_layer_speed = 30%
 +
gap_fill_speed = 20
 +
gcode_comments = 0
 +
infill_acceleration = 0
 +
infill_every_layers = 1
 +
infill_extruder = 1
 +
infill_extrusion_width = 0
 +
infill_first = 0
 +
infill_only_where_needed = 0
 +
infill_speed = 60
 +
layer_height = 0.22
 +
min_skirt_length = 0
 +
notes =
 +
only_retract_when_crossing_perimeters = 1
 +
ooze_prevention = 0
 +
output_filename_format = [input_filename_base].gcode
 +
overhangs = 1
 +
perimeter_acceleration = 0
 +
perimeter_extruder = 1
 +
perimeter_extrusion_width = 0
 +
perimeter_speed = 50
 +
perimeters = 3
 +
post_process =
 +
raft_layers = 0
 +
randomize_start = 0
 +
resolution = 0
 +
skirt_distance = 6
 +
skirt_height = 1
 +
skirts = 2
 +
small_perimeter_speed = 40
 +
solid_fill_pattern = rectilinear
 +
solid_infill_below_area = 70
 +
solid_infill_every_layers = 0
 +
solid_infill_extrusion_width = 0
 +
solid_infill_speed = 60
 +
spiral_vase = 0
 +
standby_temperature_delta = -5
 +
start_perimeters_at_concave_points = 0
 +
start_perimeters_at_non_overhang = 0
 +
support_material = 0
 +
support_material_angle = 0
 +
support_material_enforce_layers = 0
 +
support_material_extruder = 1
 +
support_material_extrusion_width = 0
 +
support_material_interface_extruder = 1
 +
support_material_interface_layers = 0
 +
support_material_interface_spacing = 0
 +
support_material_pattern = rectilinear
 +
support_material_spacing = 2.5
 +
support_material_speed = 60
 +
support_material_threshold = 0
 +
thin_walls = 1
 +
threads = 2
 +
top_infill_extrusion_width = 0
 +
top_solid_infill_speed = 50
 +
top_solid_layers = 5
 +
travel_speed = 130
 +
</pre>
 +
 +
Solide Teile:
 +
<pre style="height:200px;overflow-y:scroll;">
 +
avoid_crossing_perimeters = 0
 +
bottom_solid_layers = 3
 +
bridge_acceleration = 0
 +
bridge_flow_ratio = 1
 +
bridge_speed = 60
 +
brim_width = 3
 +
complete_objects = 0
 +
default_acceleration = 0
 +
external_perimeter_speed = 70%
 +
external_perimeters_first = 0
 +
extra_perimeters = 1
 +
extruder_clearance_height = 20
 +
extruder_clearance_radius = 20
 +
extrusion_width = 0
 +
fill_angle = 45
 +
fill_density = 0.3
 +
fill_pattern = honeycomb
 +
first_layer_acceleration = 0
 +
first_layer_extrusion_width = 200%
 +
first_layer_height = 0.22
 +
first_layer_speed = 30%
 +
gap_fill_speed = 20
 +
gcode_comments = 0
 +
infill_acceleration = 0
 +
infill_every_layers = 1
 +
infill_extruder = 1
 +
infill_extrusion_width = 0
 +
infill_first = 0
 +
infill_only_where_needed = 0
 +
infill_speed = 60
 +
layer_height = 0.22
 +
min_skirt_length = 0
 +
notes =
 +
only_retract_when_crossing_perimeters = 1
 +
ooze_prevention = 0
 +
output_filename_format = [input_filename_base].gcode
 +
overhangs = 1
 +
perimeter_acceleration = 0
 +
perimeter_extruder = 1
 +
perimeter_extrusion_width = 0
 +
perimeter_speed = 50
 +
perimeters = 3
 +
post_process =
 +
raft_layers = 0
 +
randomize_start = 0
 +
resolution = 0
 +
skirt_distance = 6
 +
skirt_height = 1
 +
skirts = 2
 +
small_perimeter_speed = 40
 +
solid_fill_pattern = concentric
 +
solid_infill_below_area = 70
 +
solid_infill_every_layers = 0
 +
solid_infill_extrusion_width = 0
 +
solid_infill_speed = 60
 +
spiral_vase = 0
 +
standby_temperature_delta = -5
 +
start_perimeters_at_concave_points = 0
 +
start_perimeters_at_non_overhang = 0
 +
support_material = 0
 +
support_material_angle = 0
 +
support_material_enforce_layers = 0
 +
support_material_extruder = 1
 +
support_material_extrusion_width = 0
 +
support_material_interface_extruder = 1
 +
support_material_interface_layers = 0
 +
support_material_interface_spacing = 0
 +
support_material_pattern = rectilinear
 +
support_material_spacing = 2.5
 +
support_material_speed = 60
 +
support_material_threshold = 0
 +
thin_walls = 1
 +
threads = 2
 +
top_infill_extrusion_width = 0
 +
top_solid_infill_speed = 50
 +
top_solid_layers = 5
 +
travel_speed = 130
 +
</pre>
 +
 
=== alte configs ===
 
=== alte configs ===
  

Version vom 15. Februar 2014, 19:55 Uhr

Eine Seite um (gute) Beispielkonfigkurationen zu sammeln, am besten mit Beispieldruck (Foto)

Es gibt vermutlich nicht die eine Ideal-Konfiguration die für alle Teile gut funktioniert, mit den hier gelisteten sollte aber ein Druck einigermaßen gelingen.

aktuelle configs

Der Drucker hat sich verändert, dementsprechend haben sich auch die configs geändert. Beispielsweise haben wir jetzt 0.5 mm Düsen an den beiden Hot Ends, nicht mehr 0.35 mm. Dazu kommt, dass das homing konstruktionsbedingt außerhalb des hot beds stattfindet, mit diesem Start-gcode wird das ausgeglichen: 

G28 X0 Y0 ; home X and Y
G0 X60; move to X60
G92 X0; set postition to X=0
G28 Z0; home Z

Das, oder etwas Ähnliches sollte in allen configs mit drin sein.

Eine funktionierende, aber noch nicht sehr fein justierte config ist diese:

larsan

# generated by Slic3r 0.9.10 on Sun Sep 29 22:51:39 2013
avoid_crossing_perimeters = 0
bed_size = 190,190
bed_temperature = 50
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 1
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off extruder temperature\n;M140 S0 ; turn off bed temperature; currently disabled\nG0 X0    ; move X axis to 0\nG92 Z0 E5 ;define current point as Z0 E5\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y198 F6000 ; drive print table all the way out\nM84     ; disable motors
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 1
extruder_clearance_radius = 30
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 180%
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 45
fill_density = 0.3
fill_pattern = honeycomb
first_layer_bed_temperature = 50
first_layer_extrusion_width = 0
first_layer_height = 0.25
first_layer_speed = 30%
first_layer_temperature = 200
g0 = 0
gap_fill_speed = 15
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
layer_gcode = 
layer_height = 0.25
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 5
min_skirt_length = 0
notes = larsanconfig
nozzle_diameter = 0.5
only_retract_when_crossing_perimeters = 1
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 80
perimeters = 3
post_process = 
print_center = 90,60
raft_layers = 0
randomize_start = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 2
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 35
rotate = 0
scale = 1
skirt_distance = 10
skirt_height = 1
skirts = 3
slowdown_below_layer_time = 30
small_perimeter_speed = 50
solid_fill_pattern = rectilinear
solid_infill_below_area = 40
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 80
spiral_vase = 0
start_gcode = G28 X0 Y0 ; home X and Y\nG0 X60; move to X60\nG92 X0; set postition to X=0\nG28 Z0; home Z
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 65
support_material_threshold = 0
temperature = 195
threads = 1
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 60
top_solid_layers = 3
travel_speed = 80
use_relative_e_distances = 0
vibration_limit = 0
wipe = 0
z_offset = 0

Kasalehlia

etwas auf den neuen Drucker angepasst. Start G-Code und neuer Lüfter am Druckkopf sind berücksichtigt.

Printer: 

bed_size = 200,200
end_gcode = M107; fan off\nM104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.5
print_center = 100,80
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
start_gcode = G28 X0 Y0 ; home X and Y\nG0 X60; move to X60\nG92 X0; set postition to X=0\nG28 Z0; home Z\nM106; fan on
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 0
z_offset = 0

Normales PLA: 

bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
first_layer_bed_temperature = 55
first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 30
temperature = 195

Holz PLA: 

bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
first_layer_bed_temperature = 55
first_layer_temperature = 210
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 30
temperature = 210

Matetags oder andere Filigranere Dinge: 

avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 3
complete_objects = 0
default_acceleration = 0
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 1
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.22
first_layer_speed = 30%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
layer_height = 0.22
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 50
perimeters = 3
post_process = 
raft_layers = 0
randomize_start = 0
resolution = 0
skirt_distance = 6
skirt_height = 1
skirts = 2
small_perimeter_speed = 40
solid_fill_pattern = rectilinear
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
start_perimeters_at_concave_points = 0
start_perimeters_at_non_overhang = 0
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 5
travel_speed = 130

Solide Teile: 

avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 3
complete_objects = 0
default_acceleration = 0
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 0.3
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.22
first_layer_speed = 30%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
layer_height = 0.22
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 50
perimeters = 3
post_process = 
raft_layers = 0
randomize_start = 0
resolution = 0
skirt_distance = 6
skirt_height = 1
skirts = 2
small_perimeter_speed = 40
solid_fill_pattern = concentric
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
start_perimeters_at_concave_points = 0
start_perimeters_at_non_overhang = 0
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 5
travel_speed = 130

alte configs

Von larsan

Ursprünglich die erste Konfiguration für unseren Drucker auf Basis von DanielWillmanns Konfiguration.

Von der unten stehenden Config gibt es eine verbesserte larsan-tuned.ini, die Rohieb gemacht hat. 

# generated by Slic3r 0.9.8-dev on Wed Nov 28 08:03:30 2012
acceleration = 0
bed_size = 180,200
bed_temperature = 50
bottom_solid_layers = 3
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 
cooling = 
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0    ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84     ; disable motors
external_perimeter_speed = 40%
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 30
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 0
fill_density = 0.15
fill_pattern = honeycomb
first_layer_bed_temperature = 50
first_layer_extrusion_width = 0
first_layer_height = 0.27
first_layer_speed = 15%
first_layer_temperature = 195
g0 = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_speed = 60
layer_gcode = 
layer_height = 0.24
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 5
min_skirt_length = 0
notes = larsanconfig
nozzle_diameter = 0.35
only_retract_when_crossing_perimeters = 
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 25
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 50
perimeters = 3
post_process = 
print_center = 90,100
randomize_start = 1
retract_before_travel = 5
retract_length = 2
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0.01
retract_restart_extra_toolchange = 0
retract_speed = 50
rotate = 0
scale = 1
skirt_distance = 20
skirt_height = 1
skirts = 3
slowdown_below_layer_time = 50
small_perimeter_speed = 100%
solid_fill_pattern = rectilinear
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_speed = 90%
start_gcode = G28 ; home all axes\nM92 E820
support_material = 
support_material_angle = 45
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 60
support_material_threshold = 41
temperature = 185
threads = 2
top_solid_infill_speed = 70%
top_solid_layers = 3
travel_speed = 50
use_relative_e_distances = 0
vibration_limit = 0
z_offset = 0

Schnelle Config von Daniel Bohrer (Work in Progress)

Der erste und letzte Layer wird "normal schnell" gedruckt, die anderen doppelt so schnell. Bei dünnen Strukturen (z.B. Mate-Tags) muss man notfalls noch ein bisschen mit der Perimeteranzahl spielen. 

# generated by Slic3r 0.9.4-dev on Fri Nov 16 20:55:02 2012
acceleration = 0
bed_size = 180,200
bed_temperature = 60
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 350
brim_width = 0
complete_objects = 0
cooling = 1
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0    ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84     ; disable motors
external_perimeter_speed = 90%
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1.0
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 0
fill_density = 0.2
fill_pattern = rectilinear
first_layer_bed_temperature = 60
first_layer_extrusion_width = 0
first_layer_height = 100%
first_layer_speed = 20%
first_layer_temperature = 195
g0 = 0
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_speed = 120
layer_gcode = 
layer_height = 0.25
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
notes = Used for Mate name tag
nozzle_diameter = 0.35
only_retract_when_crossing_perimeters = 0
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 25
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 100
perimeters = 2
post_process = 
print_center = 90,100
randomize_start = 1
retract_before_travel = 4
retract_length = 4
retract_length_toolchange = 3
retract_lift = 0.5
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 150
rotate = 0
scale = 1
skirt_distance = 10
skirt_height = 1
skirts = 2
slowdown_below_layer_time = 60
small_perimeter_speed = 80%
solid_fill_pattern = rectilinear
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_speed = 100%
solid_layers = 3
start_gcode = G28 ; home all axes\nM92 E820
support_material = 1
support_material_angle = 45
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_pattern = rectilinear
support_material_spacing = 3
support_material_threshold = 45
temperature = 185
threads = 3
top_solid_infill_speed = 50%
travel_speed = 140
use_relative_e_distances = 0
z_offset = 0.22

Für Mate-Tags

Konfiguration für Mate-Tags 

# generated by Slic3r 0.9.9-dev on Fri Jun  7 23:59:05 2013
avoid_crossing_perimeters = 1
bed_size = 180,200
bed_temperature = 50
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 50
brim_width = 0
complete_objects = 1
cooling = 
default_acceleration = 0
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0    ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84     ; disable motors
external_perimeter_speed = 50%
external_perimeters_first = 0
extra_perimeters = 
extruder_clearance_height = 36
extruder_clearance_radius = 40
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1.1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 30
fill_density = 0.3
fill_pattern = rectilinear
first_layer_bed_temperature = 50
first_layer_extrusion_width = 0
first_layer_height = 0.27
first_layer_speed = 40%
first_layer_temperature = 197
g0 = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 70
layer_gcode = 
layer_height = 0.24
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 5
min_skirt_length = 10
notes = Config used for bottle name tags (http://www.thingiverse.com/thing:38861)
nozzle_diameter = 0.33
only_retract_when_crossing_perimeters = 1
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 50
perimeters = 2
post_process = 
print_center = 90,100
raft_layers = 0
randomize_start = 
resolution = 0
retract_before_travel = 0
retract_layer_change = 1
retract_length = 2
retract_length_toolchange = 5
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 50
rotate = 0
scale = 1
skirt_distance = 5
skirt_height = 1
skirts = 2
slowdown_below_layer_time = 50
small_perimeter_speed = 60%
solid_fill_pattern = rectilinear
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 100%
start_gcode = G28 ; home all axes\nM92 E820
support_material = 
support_material_angle = 45
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 70
support_material_threshold = 41
temperature = 188
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 70%
top_solid_layers = 3
travel_speed = 50
use_relative_e_distances = 0
vibration_limit = 0
z_offset = 0

von Chrissi^

  • Nette Konfiguration zum Drucken von allem möglichen.
  • First Layer ist super langsam => Guter Druck auch bei kleinen Strukturen
  • First Layer Extrusion Width 110% => Wenig Wellenschlagen auf dem ersten Layer
# generated by Slic3r 0.9.3 on Tue Nov  6 21:53:43 2012
acceleration = 0
bed_size = 180,200
bed_temperature = 60
bridge_fan_speed = 100
bridge_flow_ratio = 1.05
bridge_speed = 60
brim_width = 0
complete_objects = 
cooling = 1
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0    ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84     ; disable motors
external_perimeter_speed = 100%
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 30
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 100%
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 45
fill_density = 0.1
fill_pattern = rectilinear
first_layer_bed_temperature = 60
first_layer_extrusion_width = 112%
first_layer_height = 95%
first_layer_speed = 15%
first_layer_temperature = 200
g0 = 0
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 120%
infill_speed = 60
layer_gcode = 
layer_height = 0.3
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 5
notes = larsanconfig
nozzle_diameter = 0.35
only_retract_when_crossing_perimeters = 1
output_filename_format = [timestamp]_[input_filename_base].gcode
perimeter_acceleration = 25
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 2
post_process = 
print_center = 120,120
randomize_start = 1
retract_before_travel = 4
retract_length = 2
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 50
rotate = 0
scale = 1
skirt_distance = 10
skirt_height = 1
skirts = 3
slowdown_below_layer_time = 50
small_perimeter_speed = 50%
solid_fill_pattern = rectilinear
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_speed = 100%
solid_layers = 3
start_gcode = G28 ; home all axes\nM92 E820
support_material = 1
support_material_angle = 45
support_material_extruder = 1
support_material_extrusion_width = 160%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_threshold = 40
temperature = 205
threads = 2
top_solid_infill_speed = 40%
travel_speed = 90
use_relative_e_distances = 0
z_offset = 0

Gelbes Filament

  • Ursprünglich für Reprap/Parent erstellt
  • Damit gedruckt: der letzte gelbe frame-vertex für den Drucker
  • etwas wärmer (195°C)
  • 0.22 mm z-offeset
acceleration = 0
bed_size = 170,170
bed_temperature = 60
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 30
brim_width = 0
complete_objects = 0
cooling = 1
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0    ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84     ; disable motors
external_perimeter_speed = 90%
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 3
fill_angle = 45
fill_density = 0.15
fill_pattern = rectilinear
first_layer_bed_temperature = 60
first_layer_extrusion_width = 0
first_layer_height = 115%
first_layer_speed = 80%
first_layer_temperature = 200
g0 = 0
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_speed = 40
layer_gcode = 
layer_height = 0.28
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
notes = Used for Mate name tag
nozzle_diameter = 0.35
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 25
perimeter_speed = 30
perimeters = 3
perimeters_extruder = 1
perimeters_extrusion_width = 0
post_process = 
print_center = 50,27
randomize_start = 1
retract_before_travel = 4
retract_length = 3
retract_lift = 0.4
retract_restart_extra = 0
retract_speed = 30
rotate = 0
scale = 1
skirt_distance = 6
skirt_height = 1
skirts = 3
slowdown_below_layer_time = 60
small_perimeter_speed = 30
solid_fill_pattern = rectilinear
solid_infill_speed = 40
solid_layers = 3
start_gcode = G28 ; home all axes\nM92 E820
support_material = 
support_material_angle = 45
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_threshold = 45
temperature = 195
threads = 2
top_solid_infill_speed = 40
travel_speed = 130
use_relative_e_distances = 0
z_offset = 0.22

RepRap-Config

Konfiguration, mit der die Teile für den RepRap vom Netz39 gedruckt wurden. 

# generated by Slic3r 0.9.9-dev on Mon Jun  3 17:06:48 2013
avoid_crossing_perimeters = 0
bed_size = 180,200
bed_temperature = 50
bottom_solid_layers = 5
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 30
brim_width = 0
complete_objects = 1
cooling = 
default_acceleration = 0
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0    ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84     ; disable motors
external_perimeter_speed = 40%
external_perimeters_first = 0
extra_perimeters = 
extruder_clearance_height = 35
extruder_clearance_radius = 62
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1.1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 30
fill_density = 0.5
fill_pattern = rectilinear
first_layer_bed_temperature = 50
first_layer_extrusion_width = 0
first_layer_height = 150%
first_layer_speed = 40%
first_layer_temperature = 197
g0 = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
layer_gcode = 
layer_height = 0.2
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 5
min_skirt_length = 15
notes = config for printing netz39 pieces
nozzle_diameter = 0.33
only_retract_when_crossing_perimeters = 1
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 3
post_process = 
print_center = 90,100
raft_layers = 0
randomize_start = 
resolution = 0
retract_before_travel = 0
retract_layer_change = 1
retract_length = 2
retract_length_toolchange = 5
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 50
rotate = 0
scale = 1
skirt_distance = 5
skirt_height = 1
skirts = 2
slowdown_below_layer_time = 50
small_perimeter_speed = 60%
solid_fill_pattern = rectilinear
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 100%
start_gcode = G28 ; home all axes\nM92 E820
support_material = 
support_material_angle = 45
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 60
support_material_threshold = 41
temperature = 188
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 70%
top_solid_layers = 5
travel_speed = 100
use_relative_e_distances = 0
vibration_limit = 0
z_offset = 0
Abgerufen von „https://stratum0.org/mediawiki/index.php?title=RepRap/Configs/Slic3r&oldid=7278“