3D-Drucker/SlicerBundle.ini

1. generated by Slic3r 1.2.9 on Sun Aug 14 14:31:08 2016

[filament:Lulzbot ABS] bed_temperature = 100 bridge_fan_speed = 50 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 2.85 first_layer_bed_temperature = 100 first_layer_temperature = 250 max_fan_speed = 0 min_fan_speed = 0 min_print_speed = 5 slowdown_below_layer_time = 20 temperature = 230

[filament:Lulzbot PLA] bed_temperature = 50 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 2.82 first_layer_bed_temperature = 50 first_layer_temperature = 200 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 5 slowdown_below_layer_time = 30 temperature = 200

[filament:Lulzbot PLA Weiß] bed_temperature = 50 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 2.85 first_layer_bed_temperature = 50 first_layer_temperature = 200 max_fan_speed = 100 min_fan_speed = 30 min_print_speed = 5 slowdown_below_layer_time = 30 temperature = 180

[filament:Lulzbot PLA black] bed_temperature = 50 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #000000 filament_diameter = 2.9 first_layer_bed_temperature = 50 first_layer_temperature = 200 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 5 slowdown_below_layer_time = 30 temperature = 200

[filament:MendelPro ABS] bed_temperature = 0 bridge_fan_speed = 100 cooling = 0 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 1.7 first_layer_bed_temperature = 0 first_layer_temperature = 250 max_fan_speed = 100 min_fan_speed = 50 min_print_speed = 5 slowdown_below_layer_time = 30 temperature = 245

[filament:MendelPro Holz] bed_temperature = 50 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 1.7 first_layer_bed_temperature = 55 first_layer_temperature = 200 max_fan_speed = 100 min_fan_speed = 50 min_print_speed = 5 slowdown_below_layer_time = 30 temperature = 185

[filament:MendelPro Mistery] bed_temperature = 80 bridge_fan_speed = 50 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 1.7 first_layer_bed_temperature = 80 first_layer_temperature = 250 max_fan_speed = 0 min_fan_speed = 0 min_print_speed = 10 slowdown_below_layer_time = 20 temperature = 200

[filament:MendelPro PLA] bed_temperature = 50 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 1.7 first_layer_bed_temperature = 55 first_layer_temperature = 200 max_fan_speed = 100 min_fan_speed = 40 min_print_speed = 5 slowdown_below_layer_time = 30 temperature = 185

[filament:MendelPro PLA fast] bed_temperature = 50 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 1.7 first_layer_bed_temperature = 50 first_layer_temperature = 200 max_fan_speed = 100 min_fan_speed = 50 min_print_speed = 5 slowdown_below_layer_time = 30 temperature = 200

[filament:MendelPro PLA transparent] bed_temperature = 50 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 1.7 first_layer_bed_temperature = 55 first_layer_temperature = 200 max_fan_speed = 100 min_fan_speed = 40 min_print_speed = 5 slowdown_below_layer_time = 30 temperature = 200

[filament:TinyBoy PLA] bed_temperature = 0 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 2 extrusion_multiplier = 0.9 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #35E1FF filament_diameter = 1.63 first_layer_bed_temperature = 0 first_layer_temperature = 200 max_fan_speed = 40 min_fan_speed = 35 min_print_speed = 5 slowdown_below_layer_time = 15 temperature = 190

[filament:prusa i3 ABS grün] bed_temperature = 100 bridge_fan_speed = 70 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #80FF00 filament_diameter = 2.9 first_layer_bed_temperature = 100 first_layer_temperature = 255 max_fan_speed = 0 min_fan_speed = 0 min_print_speed = 5 slowdown_below_layer_time = 15 temperature = 245

[filament:prusa i3 ABS grün blau] bed_temperature = 100 bridge_fan_speed = 70 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #0000A0 filament_diameter = 2.9 first_layer_bed_temperature = 100 first_layer_temperature = 240 max_fan_speed = 0 min_fan_speed = 0 min_print_speed = 5 slowdown_below_layer_time = 30 temperature = 235

[filament:prusa i3 ABS schwarz] bed_temperature = 100 bridge_fan_speed = 70 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #000000 filament_diameter = 2.9 first_layer_bed_temperature = 100 first_layer_temperature = 260 max_fan_speed = 0 min_fan_speed = 0 min_print_speed = 5 slowdown_below_layer_time = 15 temperature = 255

[filament:prusa i3 PLA] bed_temperature = 50 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 2.9 first_layer_bed_temperature = 50 first_layer_temperature = 200 max_fan_speed = 100 min_fan_speed = 50 min_print_speed = 5 slowdown_below_layer_time = 30 temperature = 190

[filament:prusa i3 PLA lila] bed_temperature = 50 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #8000FF filament_diameter = 3 first_layer_bed_temperature = 50 first_layer_temperature = 200 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 5 slowdown_below_layer_time = 15 temperature = 200

[filament:prusa i3 PLA pink] bed_temperature = 50 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #FF00FF filament_diameter = 2.83 first_layer_bed_temperature = 50 first_layer_temperature = 200 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 5 slowdown_below_layer_time = 15 temperature = 180

[presets] filament = prusa i3 ABS grün blau.ini print = Lulzbot fine sup.ini printer = Lulzbot.ini

[print:Lulzbot fine] avoid_crossing_perimeters = 1 bottom_solid_layers = 2 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 40 brim_width = 5 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 50% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 35 fill_density = 15% fill_pattern = 3dhoneycomb first_layer_acceleration = 0 first_layer_extrusion_width = 0 first_layer_height = 0.2 first_layer_speed = 10 gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 110% infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 80 interface_shells = 0 layer_height = 0.2 max_print_speed = 80 max_volumetric_speed = 0 min_skirt_length = 0 notes = only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 60 perimeters = 3 post_process = raft_layers = 0 resolution = 0 seam_position = aligned skirt_distance = 10 skirt_height = 1 skirts = 1 small_perimeter_speed = 20 solid_infill_below_area = 30 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 20 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 0 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 60 support_material_threshold = 45 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 top_solid_infill_speed = 20 top_solid_layers = 3 travel_speed = 100 xy_size_compensation = 0

[print:Lulzbot fine sup] avoid_crossing_perimeters = 1 bottom_solid_layers = 2 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 40 brim_width = 3 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 50% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 35 fill_density = 15% fill_pattern = 3dhoneycomb first_layer_acceleration = 0 first_layer_extrusion_width = 0 first_layer_height = 0.2 first_layer_speed = 10 gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 110% infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 80 interface_shells = 0 layer_height = 0.2 max_print_speed = 80 max_volumetric_speed = 0 min_skirt_length = 0 notes = only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 60 perimeters = 3 post_process = raft_layers = 0 resolution = 0 seam_position = aligned skirt_distance = 10 skirt_height = 1 skirts = 1 small_perimeter_speed = 20 solid_infill_below_area = 30 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 20 spiral_vase = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = honeycomb support_material_spacing = 2.5 support_material_speed = 60 support_material_threshold = 45 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 top_solid_infill_speed = 20 top_solid_layers = 3 travel_speed = 100 xy_size_compensation = 0

[print:MendelPro] avoid_crossing_perimeters = 0 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 40 brim_width = 1 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 20 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 15% fill_pattern = 3dhoneycomb first_layer_acceleration = 0 first_layer_extrusion_width = 0 first_layer_height = 0.2 first_layer_speed = 10 gap_fill_speed = 10 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 0 interface_shells = 0 layer_height = 0.2 max_print_speed = 80 max_volumetric_speed = 0 min_skirt_length = 2 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 0 perimeters = 2 post_process = raft_layers = 0 resolution = 0 seam_position = aligned skirt_distance = 1 skirt_height = 1 skirts = 1 small_perimeter_speed = 10 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 0 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 2 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 5 support_material_speed = 60 support_material_threshold = 40 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 top_solid_infill_speed = 20 top_solid_layers = 3 travel_speed = 100 xy_size_compensation = 0

[print:MendelPro fast] avoid_crossing_perimeters = 0 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 40 brim_width = 0 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 20 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 15% fill_pattern = 3dhoneycomb first_layer_acceleration = 0 first_layer_extrusion_width = 0 first_layer_height = 0.2 first_layer_speed = 10 gap_fill_speed = 10 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 0 interface_shells = 0 layer_height = 0.5 max_print_speed = 80 max_volumetric_speed = 0 min_skirt_length = 2 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 0 perimeters = 2 post_process = raft_layers = 0 resolution = 0 seam_position = aligned skirt_distance = 1 skirt_height = 1 skirts = 1 small_perimeter_speed = 10 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 0 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 2 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 5 support_material_speed = 60 support_material_threshold = 40 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 top_solid_infill_speed = 20 top_solid_layers = 3 travel_speed = 100 xy_size_compensation = 0

[print:MendelProSup] avoid_crossing_perimeters = 0 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 40 brim_width = 3 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 20 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 15% fill_pattern = 3dhoneycomb first_layer_acceleration = 0 first_layer_extrusion_width = 0 first_layer_height = 0.2 first_layer_speed = 10 gap_fill_speed = 10 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 0 interface_shells = 0 layer_height = 0.2 max_print_speed = 80 max_volumetric_speed = 0 min_skirt_length = 2 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 0 perimeters = 2 post_process = raft_layers = 0 resolution = 0 seam_position = aligned skirt_distance = 1 skirt_height = 1 skirts = 1 small_perimeter_speed = 10 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 0 spiral_vase = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = honeycomb support_material_spacing = 2.5 support_material_speed = 60 support_material_threshold = 40 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 top_solid_infill_speed = 20 top_solid_layers = 3 travel_speed = 100 xy_size_compensation = 0

[print:TinyBoy] avoid_crossing_perimeters = 0 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 40 brim_width = 0 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 20 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 20% fill_pattern = 3dhoneycomb first_layer_acceleration = 0 first_layer_extrusion_width = 0 first_layer_height = 0.2 first_layer_speed = 10 gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 0 interface_shells = 0 layer_height = 0.2 max_print_speed = 80 max_volumetric_speed = 0 min_skirt_length = 1 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 0 perimeters = 2 post_process = raft_layers = 0 resolution = 0 seam_position = aligned skirt_distance = 1 skirt_height = 1 skirts = 1 small_perimeter_speed = 0 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 0 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 2 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 5 support_material_speed = 0 support_material_threshold = 40 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 top_solid_infill_speed = 20 top_solid_layers = 4 travel_speed = 100 xy_size_compensation = 0

[print:TinyBoy sup] avoid_crossing_perimeters = 0 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 40 brim_width = 0 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 20 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 20% fill_pattern = 3dhoneycomb first_layer_acceleration = 0 first_layer_extrusion_width = 0 first_layer_height = 0.2 first_layer_speed = 10 gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 0 interface_shells = 0 layer_height = 0.2 max_print_speed = 80 max_volumetric_speed = 0 min_skirt_length = 1 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 0 perimeters = 2 post_process = raft_layers = 0 resolution = 0 seam_position = aligned skirt_distance = 1 skirt_height = 1 skirts = 1 small_perimeter_speed = 0 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 0 spiral_vase = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 support_material_contact_distance = 0.3 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 2 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 5 support_material_speed = 0 support_material_threshold = 40 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 top_solid_infill_speed = 20 top_solid_layers = 4 travel_speed = 100 xy_size_compensation = 0

[print:Toy] avoid_crossing_perimeters = 0 bottom_solid_layers = 2 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 0 brim_width = 0 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 0 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 0% fill_pattern = rectilinear first_layer_acceleration = 0 first_layer_extrusion_width = 0 first_layer_height = 0.2 first_layer_speed = 10 gap_fill_speed = 0 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 0 interface_shells = 0 layer_height = 0.2 max_print_speed = 10 max_volumetric_speed = 0 min_skirt_length = 1 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 0 perimeters = 2 post_process = raft_layers = 0 resolution = 0 seam_position = aligned skirt_distance = 1 skirt_height = 1 skirts = 1 small_perimeter_speed = 0 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 0 spiral_vase = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 support_material_contact_distance = 0.3 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 5 support_material_speed = 0 support_material_threshold = 40 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 top_solid_infill_speed = 0 top_solid_layers = 0 travel_speed = 100 xy_size_compensation = 0

[print:prusa i3 200] avoid_crossing_perimeters = 0 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 40 brim_width = 5 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 20 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 20% fill_pattern = 3dhoneycomb first_layer_acceleration = 0 first_layer_extrusion_width = 0 first_layer_height = 0.2 first_layer_speed = 15 gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 0 interface_shells = 0 layer_height = 0.2 max_print_speed = 60 max_volumetric_speed = 0 min_skirt_length = 1 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 0 perimeters = 2 post_process = raft_layers = 0 resolution = 0 seam_position = aligned skirt_distance = 1 skirt_height = 1 skirts = 1 small_perimeter_speed = 15 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 0 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_contact_distance = 0 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 2 support_material_interface_spacing = 0 support_material_interface_speed = 10 support_material_pattern = pillars support_material_spacing = 2.5 support_material_speed = 40 support_material_threshold = 40 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 top_solid_infill_speed = 20 top_solid_layers = 3 travel_speed = 100 xy_size_compensation = 0

[print:prusa i3 200 sup] avoid_crossing_perimeters = 0 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 40 brim_width = 5 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 20 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 20% fill_pattern = 3dhoneycomb first_layer_acceleration = 0 first_layer_extrusion_width = 0 first_layer_height = 0.2 first_layer_speed = 15 gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 0 interface_shells = 0 layer_height = 0.2 max_print_speed = 60 max_volumetric_speed = 0 min_skirt_length = 1 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 0 perimeters = 2 post_process = raft_layers = 1 resolution = 0 seam_position = aligned skirt_distance = 1 skirt_height = 1 skirts = 1 small_perimeter_speed = 15 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 0 spiral_vase = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 2 support_material_interface_spacing = 0 support_material_interface_speed = 10 support_material_pattern = pillars support_material_spacing = 2.5 support_material_speed = 40 support_material_threshold = 40 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 top_solid_infill_speed = 20 top_solid_layers = 3 travel_speed = 100 xy_size_compensation = 0

[printer:Lulzbot] bed_shape = 0x0,298x0,298x275,0x275 before_layer_gcode = end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = nozzle_diameter = 0.35 octoprint_apikey = octoprint_host = pressure_advance = 0 retract_before_travel = 2 retract_layer_change = 1 retract_length = 2 retract_length_toolchange = 3 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 20 start_gcode = G28 ; home all axes\n toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 vibration_limit = 0 wipe = 0 z_offset = 0

[printer:MendelPro] bed_shape = 0x0,220x0,220x177,0x177 before_layer_gcode = end_gcode = M104 S0  ; turn off temperature\nM140 S0;\nG28 X0  ; home X axis\nG0 Y177;\nM84  ; disable motors\n extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = nozzle_diameter = 0.5 octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C octoprint_host = pressure_advance = 0 retract_before_travel = 2 retract_layer_change = 1 retract_length = 5 retract_length_toolchange = 10 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 40 start_gcode = G28 Z  ; home Z\nG28 X Y  ; home X Y\n toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 vibration_limit = 0 wipe = 0 z_offset = 0

[printer:TinyBoy] bed_shape = 0x0,88x0,88x74,0x74 before_layer_gcode = end_gcode = M104 S0  ; turn off temperature\nG28 X0  ; home X axis\nM84  ; disable motors\n extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = nozzle_diameter = 0.4 octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C octoprint_host = pressure_advance = 0 retract_before_travel = 2 retract_layer_change = 1 retract_length = 5 retract_length_toolchange = 10 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 40 start_gcode = G28 Z  ; home Z\nG0 Z 1  ; lift Z\nG28 X Y  ; home X Y\n toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 vibration_limit = 0 wipe = 0 z_offset = 0

[printer:Toyrep] bed_shape = 0x0,125x0,125x125,0x125 before_layer_gcode = end_gcode = M104 S0 ; turn off nozzle temperature\nM84 ; disable motors extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = nozzle_diameter = 0.4 octoprint_apikey = octoprint_host = pressure_advance = 0 retract_before_travel = 2 retract_layer_change = 1 retract_length = 0 retract_length_toolchange = 3 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 10 start_gcode = \n toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 vibration_limit = 0 wipe = 0 z_offset = 0

[printer:prusa i3] bed_shape = 0x0,190x0,190x190,0x190 before_layer_gcode = end_gcode = M104 S0  ; turn off temperature\nM140 S0  ; turn off bed temp \nG28 X0  ; home X axis\nG0 Y190  ; präsent object\nM84  ; disable motors\nM81  ; Power off\n\n extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = nozzle_diameter = 0.4 octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C octoprint_host = pressure_advance = 0 retract_before_travel = 2 retract_layer_change = 1 retract_length = 5 retract_length_toolchange = 10 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 40 start_gcode = G28 Z  ; home Z\nG0 Z1  ; lift Z\nG28 X Y  ; home X Y\nG0 Y40 ; clab move toolchange_gcode = M83 ; turn on relative movement for extruder \nG1 E-5  ; retract filament 5mm \nG1 X10 Y10 Z4.000000  ; home X and Y axis leave Z at current height \nM84 E ; release extruder stepper motor from 'holding' position \n@pause ; pause print! \nG1 E0 ; reset extruder, ready to push out plastic again \nM82 ; set extruder movement back to absolute ready for next layer use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 vibration_limit = 0 wipe = 0 z_offset = 0

[settings] autocenter = 1 mode = expert