3D-Drucker/SlicerBundle.ini

1. generated by Slic3r 1.34.1-prusa3d-win64 on Tue Dec 19 18:45:57 2017

[filament:PETG 175] bed_temperature = 0 bridge_fan_speed = 100 cooling = 0 disable_fan_first_layers = 5 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_cost = 27.4375 filament_density = 1.27 filament_diameter = 1.75 filament_max_volumetric_speed = 0 filament_notes = "" filament_settings_id = first_layer_bed_temperature = 0 first_layer_temperature = 245 max_fan_speed = 100 min_fan_speed = 100 min_print_speed = 5 slowdown_below_layer_time = 20 temperature = 220

[filament:PETG 285] bed_temperature = 75 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 3 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_cost = 27.4375 filament_density = 1.27 filament_diameter = 2.85 filament_max_volumetric_speed = 0 filament_notes = "" filament_settings_id = first_layer_bed_temperature = 75 first_layer_temperature = 250 max_fan_speed = 100 min_fan_speed = 100 min_print_speed = 5 slowdown_below_layer_time = 20 temperature = 240

[filament:PLA 175] bed_temperature = 0 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 3 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_cost = 0 filament_density = 0 filament_diameter = 1.75 filament_max_volumetric_speed = 0 filament_notes = "" filament_settings_id = first_layer_bed_temperature = 0 first_layer_temperature = 230 max_fan_speed = 100 min_fan_speed = 80 min_print_speed = 10 slowdown_below_layer_time = 20 temperature = 190

[filament:PLA 285] bed_temperature = 60 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 10 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_cost = 0 filament_density = 0 filament_diameter = 2.85 filament_max_volumetric_speed = 0 filament_notes = "" filament_settings_id = first_layer_bed_temperature = 75 first_layer_temperature = 230 max_fan_speed = 100 min_fan_speed = 100 min_print_speed = 5 slowdown_below_layer_time = 20 temperature = 220

[presets] filament = PETG 175.ini print = Kossel.ini printer = Kossel.ini

[print:Kossel] avoid_crossing_perimeters = 0 bottom_solid_layers = 2 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 40 brim_width = 2 clip_multipart_objects = 0 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 ensure_vertical_shell_thickness = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 30 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 20% fill_pattern = honeycomb first_layer_acceleration = 0 first_layer_extrusion_width = 200% first_layer_height = 0.2 first_layer_speed = 10 gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 60 interface_shells = 0 layer_height = 0.2 max_print_speed = 80 max_volumetric_extrusion_rate_slope_negative = 0 max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 min_skirt_length = 0 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 60 perimeters = 3 post_process = print_settings_id = raft_layers = 0 resolution = 0 seam_position = aligned skirt_distance = 10 skirt_height = 1 skirts = 5 small_perimeter_speed = 15 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 20 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_buildplate_only = 0 support_material_contact_distance = 0.4 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = pillars support_material_spacing = 2.5 support_material_speed = 60 support_material_synchronize_layers = 0 support_material_threshold = 0 support_material_with_sheath = 1 support_material_xy_spacing = 50% thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 top_solid_infill_speed = 15 top_solid_layers = 3 travel_speed = 130 xy_size_compensation = 0

[print:Lulzbot] avoid_crossing_perimeters = 0 bottom_solid_layers = 3 bridge_acceleration = 2000 bridge_flow_ratio = 1 bridge_speed = 72 brim_width = 0 clip_multipart_objects = 0 complete_objects = 0 default_acceleration = 2000 dont_support_bridges = 1 ensure_vertical_shell_thickness = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 45 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0.42 fill_angle = 45 fill_density = 5% fill_pattern = rectilinear first_layer_acceleration = 2000 first_layer_extrusion_width = 0.53 first_layer_height = 100% first_layer_speed = 75% gap_fill_speed = 55 gcode_comments = 0 infill_acceleration = 2000 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.68 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 55% infill_speed = 80 interface_shells = 0 layer_height = 0.2 max_print_speed = 80 max_volumetric_extrusion_rate_slope_negative = 0 max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 min_skirt_length = 0 notes = only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 1200 perimeter_extruder = 1 perimeter_extrusion_width = 0.38 perimeter_speed = 75 perimeters = 2 post_process = print_settings_id = raft_layers = 0 resolution = 0 seam_position = aligned skirt_distance = 5 skirt_height = 1 skirts = 0 small_perimeter_speed = 50 solid_infill_below_area = 90 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.5 solid_infill_speed = 75 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_buildplate_only = 0 support_material_contact_distance = 0.3 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 5 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear-grid support_material_spacing = 7 support_material_speed = 60 support_material_synchronize_layers = 0 support_material_threshold = 30 support_material_with_sheath = 0 support_material_xy_spacing = 0.5 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0.4 top_solid_infill_speed = 60 top_solid_layers = 5 travel_speed = 160 xy_size_compensation = 0

[print:Mendel] avoid_crossing_perimeters = 0 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 40 brim_width = 2 clip_multipart_objects = 0 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 ensure_vertical_shell_thickness = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 30 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 20% fill_pattern = cubic first_layer_acceleration = 0 first_layer_extrusion_width = 150% first_layer_height = 0.2 first_layer_speed = 20 gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 40 interface_shells = 0 layer_height = 0.2 max_print_speed = 40 max_volumetric_extrusion_rate_slope_negative = 0 max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 min_skirt_length = 0 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 40 perimeters = 3 post_process = print_settings_id = raft_layers = 0 resolution = 0 seam_position = aligned skirt_distance = 6 skirt_height = 1 skirts = 3 small_perimeter_speed = 15 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 20 spiral_vase = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 support_material_buildplate_only = 0 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 30 support_material_pattern = pillars support_material_spacing = 2.5 support_material_speed = 40 support_material_synchronize_layers = 0 support_material_threshold = 0 support_material_with_sheath = 1 support_material_xy_spacing = 50% thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 top_solid_infill_speed = 15 top_solid_layers = 4 travel_speed = 60 xy_size_compensation = 0

[print:desktop]

[printer:Kossel] bed_shape = 79.5618x8.36228,78.2518x16.6329,76.0845x24.7214,73.0836x32.5389,69.282x40,64.7214x47.0228,59.4516x53.5304,53.5304x59.4516,47.0228x64.7214,40x69.282,32.5389x73.0836,24.7214x76.0845,16.6329x78.2518,8.36228x79.5618,0x80,-8.36228x79.5618,-16.6329x78.2518,-24.7214x76.0845,-32.5389x73.0836,-40x69.282,-47.0228x64.7214,-53.5304x59.4516,-59.4516x53.5304,-64.7214x47.0228,-69.282x40,-73.0836x32.5389,-76.0845x24.7214,-78.2518x16.6329,-79.5618x8.36228,-80x0,-79.5618x-8.36228,-78.2518x-16.6329,-76.0845x-24.7214,-73.0836x-32.5389,-69.282x-40,-64.7214x-47.0228,-59.4516x-53.5304,-53.5304x-59.4516,-47.0228x-64.7214,-40x-69.282,-32.5389x-73.0836,-24.7214x-76.0845,-16.6329x-78.2518,-8.36228x-79.5618,0x-80,8.36228x-79.5618,16.6329x-78.2518,24.7214x-76.0845,32.5389x-73.0836,40x-69.282,47.0228x-64.7214,53.5304x-59.4516,59.4516x-53.5304,64.7214x-47.0228,69.282x-40,73.0836x-32.5389,76.0845x-24.7214,78.2518x-16.6329,79.5618x-8.36228,80x0 before_layer_gcode = end_gcode = M104 S0 ; turn off nozzle temperature\nG28; Home\nM84 ; disable motors extruder_offset = 0x0,0x0,0x0 gcode_flavor = reprap layer_gcode = max_layer_height = 0.3,0.3,0.3 min_layer_height = 0.07,0.07,0.07 nozzle_diameter = 0.4,0.4,0.4 octoprint_apikey = octoprint_host = printer_settings_id = retract_before_travel = 2,2,2 retract_layer_change = 1,1,1 retract_length = 2,2,2 retract_length_toolchange = 3,3,3 retract_lift = 0,0,0 retract_lift_above = 0,0,0 retract_lift_below = 0,0,0 retract_restart_extra = 0.01,0.01,0.01 retract_restart_extra_toolchange = 0,0,0 retract_speed = 20,20,20 serial_port = serial_speed = 250000 start_gcode = ; Cyan\nM163 S0 P1\nM163 S1 P0\nM163 S2 P0\nM164 S0\n\n; Ocean\nM163 S0 P5\nM163 S1 P1\nM163 S2 P0\nM164 S1\n\n; Blue\nM163 S0 P1\nM163 S1 P1\nM163 S2 P0\nM164 S2\n\n; Violet\nM163 S0 P1\nM163 S1 P5\nM163 S2 P0\nM164 S3\n\n; Magenta\nM163 S0 P0\nM163 S1 P1\nM163 S2 P0\nM164 S4\n\n; Raspberry\nM163 S0 P0\nM163 S1 P5\nM163 S2 P1\nM164 S5\n\n; Red\nM163 S0 P0\nM163 S1 P5\nM163 S2 P1\nM164 S6\n\n; Orange\nM163 S0 P0\nM163 S1 P1\nM163 S2 P1\nM164 S7\n\n; Yellow\nM163 S0 P0\nM163 S1 P0\nM163 S2 P1\nM164 S8\n\n; Spring Green\nM163 S0 P1\nM163 S1 P0\nM163 S2 P5\nM164 S9\n\n; Green\nM163 S0 P1\nM163 S1 P0\nM163 S2 P1\nM164 S10\n\n; Turquoise\nM163 S0 P5\nM163 S1 P0\nM163 S2 P1\nM164 S11\n\n\n; Cyan-Brown\nM163 S0 P2\nM163 S1 P1\nM163 S2 P1\nM164 S12\n\n; Magenta-Brown\nM163 S0 P1\nM163 S1 P2\nM163 S2 P1\nM164 S13\n\n; Yellow-Brown\nM163 S0 P1\nM163 S1 P1\nM163 S2 P2\nM164 S14\n\n; Brown\nM163 S0 P1\nM163 S1 P1\nM163 S2 P1\nM164 S15\n toolchange_gcode = use_firmware_retraction = 1 use_relative_e_distances = 0 use_volumetric_e = 0 variable_layer_height = 0 wipe = 0,0,0 z_offset = 0

[printer:Lulzbot] bed_shape = 0x0,298x0,298x275,0x275 before_layer_gcode = end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors\n\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\n extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = max_layer_height = 0.3 min_layer_height = 0.07 nozzle_diameter = 0.35 octoprint_apikey = octoprint_host = pressure_advance = 0 printer_settings_id = retract_before_travel = 2 retract_layer_change = 1 retract_length = 5 retract_length_toolchange = 3 retract_lift = 0 retract_lift_above = 1 retract_lift_below = 0 retract_restart_extra = 0.05 retract_restart_extra_toolchange = 0 retract_speed = 60 serial_port = serial_speed = 250000 start_gcode = G28 ; home all axes\n toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 variable_layer_height = 1 wipe = 0 z_offset = 0

[printer:Mendel] bed_shape = 0x0,218x0,218x201,0x201 before_layer_gcode = end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors\n\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\n extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = max_layer_height = 0.3 min_layer_height = 0.07 nozzle_diameter = 0.5 octoprint_apikey = octoprint_host = pressure_advance = 0 printer_settings_id = retract_before_travel = 2 retract_layer_change = 1 retract_length = 2 retract_length_toolchange = 3 retract_lift = 0 retract_lift_above = 0 retract_lift_below = 0 retract_restart_extra = 0.01 retract_restart_extra_toolchange = 0 retract_speed = 20 serial_port = serial_speed = 250000 start_gcode = G28 ; home all axes\n toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 variable_layer_height = 1 wipe = 0 z_offset = 0

[printer:Tiny] bed_shape = 0x0,80x0,80x74,0x74 before_layer_gcode = end_gcode = M104 S0 ; turn off nozzle temperature\nG28 X0 ; home X axis extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = max_layer_height = 0.3 min_layer_height = 0.07 nozzle_diameter = 0.4 octoprint_apikey = octoprint_host = pressure_advance = 0 printer_settings_id = retract_before_travel = 2 retract_layer_change = 1 retract_length = 2 retract_length_toolchange = 3 retract_lift = 0 retract_lift_above = 1 retract_lift_below = 0 retract_restart_extra = 0.01 retract_restart_extra_toolchange = 0 retract_speed = 40 serial_port = serial_speed = 250000 start_gcode = G28 ; home all axes\n toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 variable_layer_height = 1 wipe = 0 z_offset = 0

[settings] autocenter = 1 mode = expert