RepRap/Configs/Slic3r
Aus Stratum 0
< RepRap | Configs
Version vom 21:00, 8. Mär. 2015 von Sintox (Diskussion | Beiträge)
Eine Seite um (gute) Beispielkonfigkurationen zu sammeln, am besten mit Beispieldruck (Foto)
Es gibt vermutlich nicht die eine Ideal-Konfiguration die für alle Teile gut funktioniert, mit den hier gelisteten sollte aber ein Druck einigermaßen gelingen.
Inhaltsverzeichnis
aktuelle configs
Der Drucker hat sich verändert, dementsprechend haben sich auch die configs geändert. Beispielsweise haben wir jetzt 0.5 mm Düsen an den beiden Hot Ends, nicht mehr 0.35 mm. Dazu kommt, dass das homing konstruktionsbedingt außerhalb des hot beds stattfindet, mit diesem Start-gcode wird das ausgeglichen:
G28 X0 Y0 ; home X and Y G0 X60; move to X60 G92 X0; set postition to X=0 G28 Z0; home Z
Das, oder etwas Ähnliches sollte in allen configs mit drin sein.
Eine funktionierende, aber noch nicht sehr fein justierte config ist diese:
Sintox
Config zum Drucken kleiner Teile mit ABS
avoid_crossing_perimeters = 0 bed_shape = 0x0,200x0,200x200,0x200 bed_temperature = 80 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_fan_speed = 100 bridge_flow_ratio = 1 bridge_speed = 60 brim_width = 0 complete_objects = 0 cooling = 1 default_acceleration = 0 disable_fan_first_layers = 1 dont_support_bridges = 1 duplicate_distance = 6 end_gcode = M104 S0 ; turn off extruder temperature\nG0 X0 ; move X axis to 0\nG1 Y198 F6000 ; drive print table all the way out\nM84 ; disable motors\n external_perimeter_extrusion_width = 0 external_perimeter_speed = 70% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extruder_offset = 0x0 extrusion_axis = E extrusion_multiplier = 1 extrusion_width = 0 fan_always_on = 1 fan_below_layer_time = 60 filament_diameter = 1.75 fill_angle = 45 fill_density = 40% fill_pattern = rectilinear first_layer_acceleration = 0 first_layer_bed_temperature = 80 first_layer_extrusion_width = 200% first_layer_height = 0.2 first_layer_speed = 40% first_layer_temperature = 240 gap_fill_speed = 20 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_speed = 20 interface_shells = 0 layer_gcode = layer_height = 0.18 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 10 min_skirt_length = 0 notes = nozzle_diameter = 0.5 only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 20 perimeters = 3 post_process = raft_layers = 0 resolution = 0 retract_before_travel = 2 retract_layer_change = 1 retract_length = 5 retract_length_toolchange = 10 retract_lift = 1 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 30 seam_position = aligned skirt_distance = 3 skirt_height = 1 skirts = 1 slowdown_below_layer_time = 30 small_perimeter_speed = 50% solid_fill_pattern = rectilinear solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extrusion_width = 0 solid_infill_speed = 20 spiral_vase = 0 standby_temperature_delta = -5 start_gcode = G28 X0 Y0 ; home X and Y\nG0 X60; move to X60\nG92 X0; set postition to X=0\nG92 Y40; set position to Y=0\nG28 Z0; home Z support_material = 1 support_material_angle = 0 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 20 support_material_threshold = 0 temperature = 240 thin_walls = 1 threads = 2 toolchange_gcode = top_infill_extrusion_width = 0 top_solid_infill_speed = 20 top_solid_layers = 3 travel_speed = 50 use_firmware_retraction = 0 use_relative_e_distances = 0 vibration_limit = 0 wipe = 0 xy_size_compensation = 0 z_offset = 0
Config zum Drucken grosser Teile mit ABS
avoid_crossing_perimeters = 0 bed_shape = 0x0,200x0,200x200,0x200 bed_temperature = 80 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_fan_speed = 100 bridge_flow_ratio = 1 bridge_speed = 60 brim_width = 0 complete_objects = 0 cooling = 1 default_acceleration = 0 disable_fan_first_layers = 1 dont_support_bridges = 1 duplicate_distance = 6 end_gcode = M84 ; disable motors\nM104 S0 ; turn off extruder temperature\nG0 X0 ; move X axis to 0\nG1 Y198 F6000 ; drive print table all the way out\nM84 ; disable motors\n external_perimeter_extrusion_width = 0 external_perimeter_speed = 70% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extruder_offset = 0x0 extrusion_axis = E extrusion_multiplier = 1 extrusion_width = 0 fan_always_on = 1 fan_below_layer_time = 60 filament_diameter = 1.75 fill_angle = 45 fill_density = 35% fill_pattern = honeycomb first_layer_acceleration = 0 first_layer_bed_temperature = 80 first_layer_extrusion_width = 200% first_layer_height = 0.25 first_layer_speed = 50% first_layer_temperature = 240 gap_fill_speed = 20 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_speed = 70 interface_shells = 0 layer_gcode = layer_height = 0.2 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 10 min_skirt_length = 0 notes = nozzle_diameter = 0.5 only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 80 perimeters = 3 post_process = raft_layers = 0 resolution = 0 retract_before_travel = 2 retract_layer_change = 1 retract_length = 5 retract_length_toolchange = 10 retract_lift = 1 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 40 seam_position = aligned skirt_distance = 2 skirt_height = 1 skirts = 1 slowdown_below_layer_time = 30 small_perimeter_speed = 30 solid_fill_pattern = rectilinear solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extrusion_width = 0 solid_infill_speed = 70 spiral_vase = 0 standby_temperature_delta = -5 start_gcode = G28 X0 Y0 ; home X and Y\nG0 X60; move to X60\nG92 X0; set postition to X=0\nG92 Y40; set position to Y=0\nG28 Z0; home Z support_material = 1 support_material_angle = 0 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 20 support_material_threshold = 0 temperature = 240 thin_walls = 1 threads = 2 toolchange_gcode = top_infill_extrusion_width = 0 top_solid_infill_speed = 60 top_solid_layers = 4 travel_speed = 130 use_firmware_retraction = 0 use_relative_e_distances = 0 vibration_limit = 0 wipe = 0 xy_size_compensation = 0 z_offset = 0
larsan
[[:RepRap/Configs/Slic3r/larsan.ini]]
Kasalehlia
etwas auf den neuen Drucker angepasst. Start G-Code und neuer Lüfter am Druckkopf sind berücksichtigt.
Printer:
bed_size = 200,200 end_gcode = M107; fan off\nM104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = nozzle_diameter = 0.5 print_center = 100,80 retract_before_travel = 2 retract_layer_change = 1 retract_length = 1 retract_length_toolchange = 10 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 30 start_gcode = G28 X0 Y0 ; home X and Y\nG0 X60; move to X60\nG92 X0; set postition to X=0\nG28 Z0; home Z\nM106; fan on toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 vibration_limit = 0 wipe = 0 z_offset = 0
Normales PLA:
bed_temperature = 50 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 60 filament_diameter = 1.75 first_layer_bed_temperature = 55 first_layer_temperature = 200 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 10 slowdown_below_layer_time = 30 temperature = 195
Holz PLA:
bed_temperature = 50 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 60 filament_diameter = 1.75 first_layer_bed_temperature = 55 first_layer_temperature = 210 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 10 slowdown_below_layer_time = 30 temperature = 210
Matetags oder andere Filigranere Dinge:
avoid_crossing_perimeters = 0 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 60 brim_width = 3 complete_objects = 0 default_acceleration = 0 external_perimeter_speed = 70% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 1 fill_pattern = rectilinear first_layer_acceleration = 0 first_layer_extrusion_width = 200% first_layer_height = 0.22 first_layer_speed = 30% gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_speed = 60 layer_height = 0.22 min_skirt_length = 0 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 50 perimeters = 3 post_process = raft_layers = 0 randomize_start = 0 resolution = 0 skirt_distance = 6 skirt_height = 1 skirts = 2 small_perimeter_speed = 40 solid_fill_pattern = rectilinear solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extrusion_width = 0 solid_infill_speed = 60 spiral_vase = 0 standby_temperature_delta = -5 start_perimeters_at_concave_points = 0 start_perimeters_at_non_overhang = 0 support_material = 0 support_material_angle = 0 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 0 support_material_interface_spacing = 0 support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 60 support_material_threshold = 0 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 top_solid_infill_speed = 50 top_solid_layers = 5 travel_speed = 130
Solide Teile:
avoid_crossing_perimeters = 0 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 60 brim_width = 3 complete_objects = 0 default_acceleration = 0 external_perimeter_speed = 70% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 0.3 fill_pattern = honeycomb first_layer_acceleration = 0 first_layer_extrusion_width = 200% first_layer_height = 0.22 first_layer_speed = 30% gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_speed = 60 layer_height = 0.22 min_skirt_length = 0 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 50 perimeters = 3 post_process = raft_layers = 0 randomize_start = 0 resolution = 0 skirt_distance = 6 skirt_height = 1 skirts = 2 small_perimeter_speed = 40 solid_fill_pattern = concentric solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extrusion_width = 0 solid_infill_speed = 60 spiral_vase = 0 standby_temperature_delta = -5 start_perimeters_at_concave_points = 0 start_perimeters_at_non_overhang = 0 support_material = 0 support_material_angle = 0 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 0 support_material_interface_spacing = 0 support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 60 support_material_threshold = 0 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 top_solid_infill_speed = 50 top_solid_layers = 5 travel_speed = 130
alte configs
Von larsan
Ursprünglich die erste Konfiguration für unseren Drucker auf Basis von DanielWillmanns Konfiguration.
Von der unten stehenden Config gibt es eine verbesserte larsan-tuned.ini, die Rohieb gemacht hat.
# generated by Slic3r 0.9.8-dev on Wed Nov 28 08:03:30 2012 acceleration = 0 bed_size = 180,200 bed_temperature = 50 bottom_solid_layers = 3 bridge_fan_speed = 100 bridge_flow_ratio = 1 bridge_speed = 60 brim_width = 0 complete_objects = cooling = disable_fan_first_layers = 1 duplicate = 1 duplicate_distance = 6 duplicate_grid = 1,1 end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors external_perimeter_speed = 40% extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 30 extruder_offset = 0x0 extrusion_axis = E extrusion_multiplier = 1 extrusion_width = 0 fan_always_on = 0 fan_below_layer_time = 60 filament_diameter = 1.75 fill_angle = 0 fill_density = 0.15 fill_pattern = honeycomb first_layer_bed_temperature = 50 first_layer_extrusion_width = 0 first_layer_height = 0.27 first_layer_speed = 15% first_layer_temperature = 195 g0 = 0 gap_fill_speed = 20 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 50 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_speed = 60 layer_gcode = layer_height = 0.24 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 5 min_skirt_length = 0 notes = larsanconfig nozzle_diameter = 0.35 only_retract_when_crossing_perimeters = output_filename_format = [input_filename_base].gcode perimeter_acceleration = 25 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 50 perimeters = 3 post_process = print_center = 90,100 randomize_start = 1 retract_before_travel = 5 retract_length = 2 retract_length_toolchange = 3 retract_lift = 0 retract_restart_extra = 0.01 retract_restart_extra_toolchange = 0 retract_speed = 50 rotate = 0 scale = 1 skirt_distance = 20 skirt_height = 1 skirts = 3 slowdown_below_layer_time = 50 small_perimeter_speed = 100% solid_fill_pattern = rectilinear solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_speed = 90% start_gcode = G28 ; home all axes\nM92 E820 support_material = support_material_angle = 45 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_pattern = rectilinear support_material_spacing = 2 support_material_speed = 60 support_material_threshold = 41 temperature = 185 threads = 2 top_solid_infill_speed = 70% top_solid_layers = 3 travel_speed = 50 use_relative_e_distances = 0 vibration_limit = 0 z_offset = 0
von Chrissi^
- Nette Konfiguration zum Drucken von allem möglichen.
- First Layer ist super langsam => Guter Druck auch bei kleinen Strukturen
- First Layer Extrusion Width 110% => Wenig Wellenschlagen auf dem ersten Layer
# generated by Slic3r 0.9.3 on Tue Nov 6 21:53:43 2012 acceleration = 0 bed_size = 180,200 bed_temperature = 60 bridge_fan_speed = 100 bridge_flow_ratio = 1.05 bridge_speed = 60 brim_width = 0 complete_objects = cooling = 1 disable_fan_first_layers = 1 duplicate = 1 duplicate_distance = 6 duplicate_grid = 1,1 end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors external_perimeter_speed = 100% extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 30 extruder_offset = 0x0 extrusion_axis = E extrusion_multiplier = 1 extrusion_width = 100% fan_always_on = 0 fan_below_layer_time = 60 filament_diameter = 1.75 fill_angle = 45 fill_density = 0.1 fill_pattern = rectilinear first_layer_bed_temperature = 60 first_layer_extrusion_width = 112% first_layer_height = 95% first_layer_speed = 15% first_layer_temperature = 200 g0 = 0 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 50 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 120% infill_speed = 60 layer_gcode = layer_height = 0.3 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 5 notes = larsanconfig nozzle_diameter = 0.35 only_retract_when_crossing_perimeters = 1 output_filename_format = [timestamp]_[input_filename_base].gcode perimeter_acceleration = 25 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 60 perimeters = 2 post_process = print_center = 120,120 randomize_start = 1 retract_before_travel = 4 retract_length = 2 retract_length_toolchange = 3 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 50 rotate = 0 scale = 1 skirt_distance = 10 skirt_height = 1 skirts = 3 slowdown_below_layer_time = 50 small_perimeter_speed = 50% solid_fill_pattern = rectilinear solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_speed = 100% solid_layers = 3 start_gcode = G28 ; home all axes\nM92 E820 support_material = 1 support_material_angle = 45 support_material_extruder = 1 support_material_extrusion_width = 160% support_material_pattern = rectilinear support_material_spacing = 2 support_material_threshold = 40 temperature = 205 threads = 2 top_solid_infill_speed = 40% travel_speed = 90 use_relative_e_distances = 0 z_offset = 0
Gelbes Filament
- Ursprünglich für Reprap/Parent erstellt
- Damit gedruckt: der letzte gelbe frame-vertex für den Drucker
- etwas wärmer (195°C)
- 0.22 mm z-offeset
acceleration = 0 bed_size = 170,170 bed_temperature = 60 bridge_fan_speed = 100 bridge_flow_ratio = 1 bridge_speed = 30 brim_width = 0 complete_objects = 0 cooling = 1 disable_fan_first_layers = 1 duplicate = 1 duplicate_distance = 6 duplicate_grid = 1,1 end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors external_perimeter_speed = 90% extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_axis = E extrusion_multiplier = 1 extrusion_width = 0 fan_always_on = 0 fan_below_layer_time = 60 filament_diameter = 3 fill_angle = 45 fill_density = 0.15 fill_pattern = rectilinear first_layer_bed_temperature = 60 first_layer_extrusion_width = 0 first_layer_height = 115% first_layer_speed = 80% first_layer_temperature = 200 g0 = 0 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 50 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_speed = 40 layer_gcode = layer_height = 0.28 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 10 notes = Used for Mate name tag nozzle_diameter = 0.35 output_filename_format = [input_filename_base].gcode perimeter_acceleration = 25 perimeter_speed = 30 perimeters = 3 perimeters_extruder = 1 perimeters_extrusion_width = 0 post_process = print_center = 50,27 randomize_start = 1 retract_before_travel = 4 retract_length = 3 retract_lift = 0.4 retract_restart_extra = 0 retract_speed = 30 rotate = 0 scale = 1 skirt_distance = 6 skirt_height = 1 skirts = 3 slowdown_below_layer_time = 60 small_perimeter_speed = 30 solid_fill_pattern = rectilinear solid_infill_speed = 40 solid_layers = 3 start_gcode = G28 ; home all axes\nM92 E820 support_material = support_material_angle = 45 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_threshold = 45 temperature = 195 threads = 2 top_solid_infill_speed = 40 travel_speed = 130 use_relative_e_distances = 0 z_offset = 0.22
RepRap-Config
Konfiguration, mit der die Teile für den RepRap vom Netz39 gedruckt wurden.
# generated by Slic3r 0.9.9-dev on Mon Jun 3 17:06:48 2013 avoid_crossing_perimeters = 0 bed_size = 180,200 bed_temperature = 50 bottom_solid_layers = 5 bridge_acceleration = 0 bridge_fan_speed = 100 bridge_flow_ratio = 1 bridge_speed = 30 brim_width = 0 complete_objects = 1 cooling = default_acceleration = 0 disable_fan_first_layers = 1 duplicate = 1 duplicate_distance = 6 duplicate_grid = 1,1 end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors external_perimeter_speed = 40% external_perimeters_first = 0 extra_perimeters = extruder_clearance_height = 35 extruder_clearance_radius = 62 extruder_offset = 0x0 extrusion_axis = E extrusion_multiplier = 1.1 extrusion_width = 0 fan_always_on = 0 fan_below_layer_time = 60 filament_diameter = 1.75 fill_angle = 30 fill_density = 0.5 fill_pattern = rectilinear first_layer_bed_temperature = 50 first_layer_extrusion_width = 0 first_layer_height = 150% first_layer_speed = 40% first_layer_temperature = 197 g0 = 0 gap_fill_speed = 20 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_speed = 60 layer_gcode = layer_height = 0.2 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 5 min_skirt_length = 15 notes = config for printing netz39 pieces nozzle_diameter = 0.33 only_retract_when_crossing_perimeters = 1 output_filename_format = [input_filename_base].gcode perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 60 perimeters = 3 post_process = print_center = 90,100 raft_layers = 0 randomize_start = resolution = 0 retract_before_travel = 0 retract_layer_change = 1 retract_length = 2 retract_length_toolchange = 5 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 50 rotate = 0 scale = 1 skirt_distance = 5 skirt_height = 1 skirts = 2 slowdown_below_layer_time = 50 small_perimeter_speed = 60% solid_fill_pattern = rectilinear solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_extrusion_width = 0 solid_infill_speed = 100% start_gcode = G28 ; home all axes\nM92 E820 support_material = support_material_angle = 45 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_layers = 0 support_material_interface_spacing = 0 support_material_pattern = rectilinear support_material_spacing = 2 support_material_speed = 60 support_material_threshold = 41 temperature = 188 threads = 2 toolchange_gcode = top_infill_extrusion_width = 0 top_solid_infill_speed = 70% top_solid_layers = 5 travel_speed = 100 use_relative_e_distances = 0 vibration_limit = 0 z_offset = 0
