RepRap/Configs/Slic3r

Die Slic3r-Konfigurationen sind nach den einzelnen Tabs aufgetrennt. Zum Importieren auf den entsprechenden Tab wechseln, Datei über „File“ → „Load Config“ importieren, dann auf den kleinen Speichern-Button (Disketten-Icon) neben der Auswahlbox klicken.

Es gibt vermutlich nicht die eine Ideal-Konfiguration die für alle Teile gut funktioniert. Die hier gelisteten Basis-Konfigurationen basieren auf den sehr konservativ ausgelegten, originalen Versionen von RepRapPro, mit denen jeder Druck (wenn auch nur langsam) gelingen sollte.

Print Settings

Bei Infill und Anzahl Perimetern kann je nach benötigter Stabilität experimentiert werden.

print-pla-0.3mm.ini (Download)

# generated by Slic3r 1.2.9 on Fri Jan 29 00:58:11 2016
avoid_crossing_perimeters = 1
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 30
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 26
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.5
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0.5
first_layer_height = 0.3
first_layer_speed = 20
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.5
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 50
interface_shells = 0
layer_height = 0.3
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 10
notes = based on the official RepRapPro "Mendel PLA 05 nozzle.ini" from https://github.com/reprappro/profiles/archive/v1.0.tar.gz
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base]_Mendel_PLA.gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.5
perimeter_speed = 32
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 3
skirt_height = 1
skirts = 1
small_perimeter_speed = 26
solid_infill_below_area = 5
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 40
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 85%
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 6
support_material_speed = 20
support_material_threshold = 45
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 32
top_solid_layers = 4
travel_speed = 250
xy_size_compensation = 0

print-abs-0.3mm.ini (Download)

# generated by Slic3r 1.2.9 on Fri Jan 29 00:56:08 2016
avoid_crossing_perimeters = 1
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 30
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 26
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.5
fill_angle = 45
fill_density = 15%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 0.5
first_layer_height = 0.3
first_layer_speed = 20
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.5
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 50
interface_shells = 0
layer_height = 0.3
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 10
notes = based on the official RepRapPro "Mendel ABS 05 nozzle.ini" from https://github.com/reprappro/profiles/archive/v1.0.tar.gz
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base]_Mendel_ABS.gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.5
perimeter_speed = 32
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 26
solid_infill_below_area = 5
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 40
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 85%
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 6
support_material_speed = 20
support_material_threshold = 45
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 32
top_solid_layers = 3
travel_speed = 250
xy_size_compensation = 0

Filament Settings

Temperaturen müssen unter Umständen an das verwendete Filament angepasst werden. Ask your local dealer.

filament-pla-1.75mm.ini (Download)

# generated by Slic3r 1.2.9 on Thu Jan 28 19:59:17 2016
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #35E1FF
filament_diameter = 1.75
first_layer_bed_temperature = 55
first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 5
slowdown_below_layer_time = 15
temperature = 190

filament-abs-1.75mm.ini (Download)

# generated by Slic3r 1.2.9 on Sun Jan 17 04:02:31 2016
bed_temperature = 105
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 0.9
fan_always_on = 0
fan_below_layer_time = 999
filament_colour = #FFFFFF
filament_diameter = 1.75
first_layer_bed_temperature = 105
first_layer_temperature = 240
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 5
temperature = 240

Printer Settings

printer.ini (Download)

# generated by Slic3r 1.2.9 on Thu Jan 28 20:04:50 2016
bed_shape = 0x0,200x0,200x177,0x177
before_layer_gcode = 
end_gcode = M104 S0        ; turn off temperature\nM140 S0        ; Bed off\nG28 X0           ; home X axis\nG0 Y177         ; moving Bed out\nM84               ; disable motors\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.5
octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C
octoprint_host = rapsberry:5000
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 5
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
start_gcode = G28 Z0            ; home Z\nG1 Z10         ; if bed is not level, don't scratch bed when homing XY\nG28 X0 Y0         ; home X Y\nG28 Z0
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = 0